Compressed air is often called the fourth utility, after electricity, water and gas. Unlike the other three, it is rarely metered. Most sites know exactly what they spend on power, but very few know how much air each machine, line or building uses, or how much is simply leaking away.

That blind spot is expensive. The NSW Government’s energy efficiency guide to compressed air systems reports that typically between 25% and 45% of compressed air is lost through leaks. It also notes that energy makes up as much as 85% of the total cost of compressed air over a compressor’s life. A compressed air flow meter is the tool that turns that hidden cost into a number you can act on.

This guide is written for plant, maintenance and energy managers. It explains why metering compressed air matters, where to install meters, which meter types suit which jobs, and what to look for when you buy.

Why meter compressed air?

Compressed air is one of the most expensive forms of energy on a site. A compressor turns electricity into air, then a large share of that energy is lost as heat. Every litre that leaks, is used for an inappropriate job, or is generated at a higher pressure than needed adds directly to the power bill.

Metering gives you the data to manage that cost:

  • Find and size leaks. Measuring flow when production is stopped (nights, weekends or shutdowns) shows the baseline leakage. Repeat the measurement after a leak repair program to prove the saving.
  • Allocate costs. Sub-metering lines, departments or tenants shows who is using the air, so costs can be charged fairly and wasteful users identified.
  • Right-size compressors. Knowing real demand profiles helps you avoid buying a larger compressor than you need, or running two machines when one would do.
  • Spot problems early. A sudden rise in consumption on a line can indicate a failed drain, a stuck valve or a new leak.
  • Support energy reporting. Measured data makes efficiency projects easier to justify and verify.

Where to install compressed air flow meters

Where you place a meter depends on the question you want it to answer. Most sites start with one or two key points and expand from there.

1. At the compressor room outlet

A meter after the dryer and receiver measures the total air leaving the compressor room. Combined with the compressors’ power use, this gives you the system’s overall efficiency and a clear picture of demand across the day and week. It is also the simplest place to measure baseline leakage when production is stopped.

2. On main branch lines

Meters on the main headers to each building, production line or department show where the air is going. This is the basis for cost allocation and helps you target leak surveys at the areas with the highest unexplained use.

3. At individual machines or processes

Point-of-use metering confirms the consumption of a specific machine, blow-off nozzle, purge or test bench. It is useful for verifying equipment specifications, setting up processes correctly, and checking that an improvement such as a new nozzle or a shut-off valve has delivered the expected saving.

Types of compressed air flow meter

There is no single best meter for compressed air. The right choice depends on pipe size, pressure, how you want to read the data, and whether the meter is for a quick check or for permanent monitoring.

Variable area (rotameter) meters

A variable area meter uses a float that rises in a tapered tube as flow increases, giving a direct visual reading with no power supply. Glass tube meters are well suited to lower-pressure applications and point-of-use measurement, such as checking the flow to a purge, a test rig or a nozzle. The Clearview 7200 series is a popular example for gas service.

For higher pressures and tougher conditions, all-metal variable area meters with a local display are a common choice for compressed air. The Kobold BGN metal tube flow meter is designed for liquid or gaseous products and suits demanding industrial service.

Digital and in-line gas flow meters

Digital gas flow meters provide an electronic display and, on many models, outputs for data logging. They suit applications where you want to track consumption over time rather than take a single reading. Our gas flow meter range includes digital and in-line options suitable for compressed air monitoring.

Flow transmitters

Where flow data needs to go to a PLC, SCADA or energy management system, a meter with a transmitter output (typically 4–20 mA or pulse) is the practical option. Options include transmitter units such as the TX175/TX300 series. This turns a local reading into a permanent record you can trend, alarm and report on.

Other technologies

Thermal mass, vortex and differential pressure meters are also widely used for compressed air, particularly on larger mains and for permanent energy monitoring. Each has strengths and limitations around pipe size, pressure loss, dry versus wet air, and the straight pipe run required. If you are comparing technologies, our guide to gas flow meters for compressed air, LPG and natural gas is a good starting point. You can also ask our team to recommend an option for your system.

What to look for in a compressed air flow meter

Use this checklist to narrow down your options before requesting a quote.

  1. Pipe size and connection. Meters are sized to the line. Check the internal diameter, connection type and whether the meter is in-line or insertion.
  2. Flow range. Choose a meter whose range covers both your lowest flow (for leak measurement at night) and your peak demand. A meter that is oversized will read poorly at low flows.
  3. Operating pressure and temperature. Check the maximum working pressure of the meter and its fittings, and the air temperature at the installation point.
  4. Accuracy and units. Understand whether accuracy is stated as a percentage of reading or of full scale. Compressed air is usually reported in normalised units such as Nm³/h or standard litres per minute, which remove the effect of pressure and temperature. Make sure the meter reports in the units your team will use.
  5. Air quality. Moisture, oil and particles can affect some meter types. Install meters after the dryer and filters where possible.
  6. Outputs and data. Decide whether a local reading is enough or whether you need 4–20 mA, pulse or digital communications for logging and alarms.
  7. Pressure drop. Every meter adds some restriction. On large mains, choose a design with a low pressure drop so the meter does not add to your energy costs.
  8. Installation requirements. Check the straight pipe lengths needed before and after the meter, and whether it can be installed under pressure or needs a shutdown.

How to use metering data to cut energy costs

Installing a meter is only the first step. The savings come from what you do with the data.

  1. Measure your baseline. Record flow during a production shutdown. Any flow when nothing should be running is almost entirely leakage and constant bleeds.
  2. Run a leak survey. Tag and repair leaks, starting with the largest. Many sites use ultrasonic detectors to find them; the NSW guide notes this approach can reduce leakage to under 5%.
  3. Measure again. Compare the new baseline with the old one. The difference, multiplied by your cost per unit of air, is your saving.
  4. Review inappropriate uses. Open blowing, cabinet cooling and other jobs that could be done with a blower, fan or electric tool are common culprits. Point-of-use meters show how much each one costs.
  5. Review pressure. Generating at a higher pressure than the highest real need wastes energy. Flow and pressure data together help you set the lowest pressure that still serves the plant.
  6. Keep monitoring. Leaks come back. A permanent meter with an alarm or a regular reading routine stops the savings from slowly eroding.

How to put a dollar figure on compressed air

Managers are more likely to act on a cost than on a flow rate. Once you have metered flow, converting it into dollars is straightforward:

  1. Find your compressor’s specific power. This is the electrical power needed to produce a given flow of air, usually in kW per m³/min. It is published on compressor data sheets, or you can calculate it from measured power and measured flow.
  2. Multiply by the flow you want to cost. For example, the leakage flow measured during a shutdown, or the flow used by a particular machine.
  3. Multiply by the hours it occurs. Leaks run whenever the system is pressurised, often 24 hours a day if the compressors are never switched off.
  4. Multiply by your electricity price. Use your actual tariff, including demand charges where relevant.

The result is the annual energy cost of that air. Repeating the calculation after repairs shows the saving in dollars, which makes it much easier to justify a leak program, a new meter or a compressor upgrade.

Building the case for permanent metering

A one-off audit is valuable, but the benefits fade as new leaks appear and production changes. Permanent meters on the compressor outlet and main branches keep the information current. They also allow simple alarms, for example an alert if overnight flow rises above the agreed baseline. On sites with several compressors, flow data alongside compressor power helps confirm the control system is running the most efficient combination of machines. Over a few years, these ongoing savings usually far outweigh the cost of the meters themselves.

Common mistakes to avoid

  • Installing a meter too close to elbows, valves or the compressor, where turbulent flow affects the reading.
  • Choosing a meter sized for peak flow only, so it cannot read the low flows that reveal leakage.
  • Mixing up actual and normalised units when comparing readings with compressor specifications.
  • Installing a meter before the dryer, where condensate can affect accuracy and reliability.
  • Taking one reading and never measuring again.

Compressed air flow meters from BES Flowmeters

BES Flowmeters supplies air flow meters for compressed air and other process gases, from glass tube variable area meters for point-of-use checks to all-metal meters, digital gas meters and transmitters for permanent monitoring. Tell us your pipe size, pressure, flow range and how you want to read the data, and we will help you choose the right meter for the job.

Request a quote or contact the team to discuss your compressed air system.

Not sure which meter suits your application? Call BES Flowmeters on (03) 5956 8685 or email sales@besflowmeters.com.au and our team will help you match the right meter to your pipe, fluid and budget.

Frequently Asked Questions

What is the best flow meter for compressed air?

It depends on the pipe size, pressure and how you want to use the data. Variable area meters suit point-of-use checks and lower pressures, all-metal variable area meters suit higher pressures, and digital meters or transmitters suit permanent monitoring and data logging.

How much compressed air is lost to leaks?

The NSW Government’s compressed air energy efficiency guide reports that typically between 25% and 45% of compressed air is lost through leaks. Metering flow during a production shutdown is a practical way to measure your own site’s leakage.

Where should a compressed air flow meter be installed?

Start at the compressor room outlet, after the dryer and receiver, to measure total demand and leakage. Then add meters on main branch lines or individual machines to see where the air is used.

What units are used to measure compressed air flow?

Compressed air is usually reported in normalised units such as Nm³/h or standard litres per minute. These correct for pressure and temperature, so readings can be compared fairly with compressor ratings and across different points in the system.

Can an air flow meter help reduce energy costs?

Yes. Metering shows your baseline leakage, identifies high-use areas and machines, and proves the savings from leak repairs and pressure reductions, so you can target the actions that cut the most energy.